manualshive.com logo in svg

ABB NPBA-01, Руководство по установке и запуску

Поделиться
Скачать
ABB NPBA-01 Скачать руководство пользователя страница 26

Chapter 5 – Programming

5-7

Installation and Start-up Guide for NPBA-01

Analogue Outputs

The PROFIBUS master can read one actual signal from the drive at a 
time. Two actual signals can be preset, and the selection between the 
two signals is done with bit 11 of the Control Word (see Chapter 6, 
Table 6-3). These parameters can only be set when the drive is 
stopped.

15.1 ANALOGUE

OUTPUT1

This parameter selects Analogue output 1 of the ACS 600 and Actual 
signal 1 available through the communication (fieldbus adapter) 
module.

NOT USED, P SPEED, ..., CONTROL DEV
All the available alternatives are presented in Appendix A, Table A-1.

15.6 ANALOGUE

OUTPUT2

This parameter selects Analogue output 2 of the ACS 600 and Actual 
signal 2 available through the communication (fieldbus adapter) 
module. 

NOT USED, P SPEED, ..., CONTROL DEV
All the available alternatives are presented in Appendix A, Table A-1.

System Control Inputs

The ACS 600 drive can receive the system control inputs from the 
digital inputs and from the communication (fieldbus adapter) module. 

 

16.1 RUN ENABLE

This parameter defines the source of the Run enable signal.

YES
The Run enable signal is set active. The ACS 600 is ready to start 
without an external Run enable signal.

DI1,...,DI6
The Run enable signal is received through a digital input. See the 

ACS 

600 Programming Manual for more information.

COMM.MODULE 

(Recommended Setting)

The Run enable signal is received through the communication (fieldbus 
adapter) module.

16.4 FAULT RESET SEL

This parameter defines where faults are reset from.
(See also the 

ACS 600 Programming Manual.)

NOT SEL
Fault reset is executed from the Control Panel.

DI1, ..., DI6
Fault reset is executed from an external switch or from the Control 
Panel.

COMM.MODULE 

(Recommended Setting)

Fault reset is executed via the communication (fieldbus adapter) 
module or from the Control Panel.

Содержание NPBA-01





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды