manualshive.com logo in svg

ABB NPBA-01, Руководство по установке и запуску

Поделиться
Скачать
ABB NPBA-01 Скачать руководство пользователя страница 15

Chapter 3 – Mechanical Installation

Installation and Start-up Guide for NPBA-01

3-3

Mounting Inside 
the ACS 601

The work inside the frequency converter should be carried out by a 
qualified electrician only. 

WARNING! Pay attention to the slowly discharging voltage of the 
capacitor bank and the voltages that are connected from external 
control circuits to the digital inputs and to the relay outputs.

WARNING! Do not touch the printed circuit boards. The integrated 
circuits are extremely sensitive to electrostatic discharge. 

Mounting instructions:

1. Stop the drive.

2. Switch off the power supply of the drive and all dangerous 

voltages connected to the digital inputs and relay outputs.

3. Wait for five minutes to ensure that the capacitors in the 

intermediate circuit have discharged. 

4. Remove the front cover of the converter.

5. Ensure that the mains cable, motor cable and capacitor bank 

(UDC+ and UDC-) are not powered.

6. Locate the position for the module (see 

Appendix E - Assembly 

Drawings). Remove the two screws from the assembly plate. 
Fasten the mounting rail to its place using the two screws.

7. Push the module onto the rail. The module can be released by 

pulling the locking spring with a screwdriver (see Figure 3-1).

Содержание NPBA-01





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды