ABB NPBA-01 Скачать руководство пользователя страница 60

Страница: 60 / 68

Installation and Start-up Guide for NPBA-01

D-1

Appendix D – Ambient Conditions

Ambient Conditions,
Operation

Ambient operating conditions refer to the conditions the option module
is subjected to when installed for stationary use.

Air Temperature: 0 to +50

Relative Humidity: 5 to 95 %, no condensation allowed. Maximum
allowed relative humidity is 60 % in the presence of corrosive gases.

Contamination Levels:
Chemical gases: IEC 721-3-3, Class 3C2
Solid particles: IEC 721-3-3, Class 3S2

Installation Site Altitude: 0 to 2000 m. If installation site is above
2000 m, contact local ABB representative.

Vibration: Max 1.5 mm (2 to 9 Hz), max 5 m/s

(9 to 200 Hz)

sinusoidal (IEC 68-2-6)

Shock: Max 70 m/s

, 22 ms (IEC 68-2-27)

Ambient Conditions,
Storage

Ambient storage conditions refer to the conditions the option module is
subjected to during storage in the protective package.

Temperature: -40 to +70

Relative Humidity: Less than 95 %, no condensation allowed

Atmospheric Pressure: 70 to 106 kPa

Vibration: Max 1.5 mm (2 to 9 Hz), max 5 m/s

(9 to 200 Hz)

sinusoidal (IEC 68-2-6)

Shock: Max 100 m/s

, 11 ms (IEC 68-2-27)

Ambient Conditions,
Transportation

Ambient transportation conditions refer to the conditions the option
module is subjected to during transportation in the protective package.

Temperature: -40 to +70

Relative Humidity: Less than 95 %, no condensation allowed.

Atmospheric Pressure: 60 to 106 kPa

Vibration: Max 3.5 mm (2 to 9 Hz), max 15 m/s

(9 to 200 Hz)

sinusoidal (IEC 68-2-6)

Shock: Max 100 m/s

, 11 ms (IEC 68-2-27)

Bump: Max 300 m/s

, 6 ms (IEC 68-2-29)

Free Fall: 250 mm

Содержание NPBA-01




































































Результаты поиска

Содержание NPBA-01

Отзывы:

Бренды по названию

Популярные бренды

ABB NPBA-01, Руководство по установке и запуску

Результаты поиска

Содержание NPBA-01

Отзывы:

Бренды по названию

Популярные бренды