ZyXEL Communications RGS Series User Manual Download Page 197 | Manualshive

Page: 197 / 259

background image

197

5.4.24 Switch – RMON Statistics

This page provides an overview of RMON Statistics entries. Each page shows up to 99 entries from the

Statistics table, default being 20, selected through the "entries per page" input field. When first visited, the web
page will show the first 20 entries from the beginning of the Statistics table. The first displayed will be the one
with the lowest ID found in the Statistics table.

Object

Description

ID

Indicates the index of Statistics entry.

Data Source(iflndex)

The port ID which wants to be monitored.

Drop

The total number of events in which packets were dropped by the probe due to lack of
resources.

Octets

The total number of octets of data (including those in bad packets) received on the
network.

Pkts

The total number of packets (including bad packets, broadcast packets, and multicast
packets) received.

Broad-cast

The total number of good packets received that were directed to the broadcast
address.

Multi-cast

The total number of good packets received that were directed to a multicast address.

CRC Errors

The total number of packets received that had a length (excluding framing bits, but
including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad
Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad
FCS with a non-integral number of octets (Alignment Error).

Under-Size

The total number of packets received that were less than 64 octets.

Over-size

The total number of packets received that were longer than 1518 octets.

Frag.

The number of frames which size is less than 64 octets received with invalid CRC.

Jabb.

The number of frames which size is larger than 64 octets received with invalid CRC.

Coll.

The best estimate of the total number of collisions on this Ethernet segment.

64

The total number of packets (including bad packets) received that were 64 octets in
length.

65~127

The total number of packets (including bad packets) received that were between 65
and 127 octets in length.

128~255

The total number of packets (including bad packets) received that were between 128
and 255 octets in length.

256~511

The total number of packets (including bad packets) received that were between 256
and 511 octets in length.

512~1023

The total number of packets (including bad packets) received that were between 512
and 1023 octets in length.

1024~1588

The total number of packets (including bad packets) received that were between 1024
and 1588 octets in length.

«
...
195
196
197
198
199
...
»

Summary of Contents for RGS Series




































































































































































































































































Reviews:

No comments

Related manuals for RGS Series

SmartCell 6A000

Brand: Cabletron Systems Pages: 114

Brand: Cabletron Systems Pages: 62

CyberSWITCH CSX150

Brand: Cabletron Systems Pages: 49

Cabletron CyberSWITCH CSX5500

Brand: Cabletron Systems Pages: 729

S5500-SI Series

Brand: H3C Pages: 130

S5500-EI series

Brand: H3C Pages: 19

S5500-EI series

Brand: H3C Pages: 91

S5500-EI series

Brand: H3C Pages: 24

S5500-EI series

Brand: H3C Pages: 69

S5120-SI Series

Brand: H3C Pages: 4

S5120-SI Series

Brand: H3C Pages: 209

S5120-SI Series

Brand: H3C Pages: 70

S5120-EI Series

Brand: H3C Pages: 32

Brand: H3C Pages: 83

Brand: H3C Pages: 26

S5500-SI Series

Brand: H3C Pages: 6

Brand: Zektor Pages: 17

SmartSwitch 6500

Brand: Cabletron Systems Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands