ZyXEL Communications RGS Series User Manual Download Page 132 | Manualshive

Page: 132 / 259

background image

132

Tx only

The switch will drop

information received from neighbors, but will send

out

information.

Disabled

The switch will not send out

information, and will drop

information received from neighbors.

Enabled

The switch will send out

information, and will analyze

information received from neighbors.

CDP Aware

Select

awareness.

operation is restricted to decoding incoming

frames (The switch

doesn't transmit

frames).

frames are only decoded if

on the port is

enabled.
Only

TLVs that can be mapped to a corresponding field in the

neighbors'

table are decoded. All other TLVs are discarded (Unrecognized CDP TLVs and
discarded CDP frames are not shown in the LLDP statistics.).

TLVs are mapped

onto

neighbors' table as shown below.

TLV "Device ID" is mapped to the

"Chassis ID" field.

TLV "Address" is mapped to the

"Management Address" field. The

address TLV can contain multiple addresses, but only the first address is shown in the

neighbors table.

TLV "Port ID" is mapped to the

"Port ID" field.

TLV "Version and Platform" is mapped to the

"System Description" field.

Both the

support "system capabilities", but the

capabilities cover

capabilities that are not part of the

. These capabilities are shown as "others" in

neighbors' table.

If all ports have

awareness disabled the switch forwards

frames received

from neighbor devices. If at least one port has

awareness enabled all

frames are terminated by the switch.
Note: When

awareness on a port is disabled the

information isn't removed

immediately, but gets removed when the hold time is exceeded.

Port Descr

: When checked the "port description" is included in

information

transmitted.

Sys Name

: When checked the "system name" is included in

information

transmitted.

Sys Descr

: When checked the "system description" is included in

information

transmitted.

Sys Capa

: When checked the "system capability" is included in

information

transmitted.

Mgmt Addr

: When checked the "management address" is included in

information transmitted.

Buttons

Click to apply changes.

Click to undo any changes made locally and revert to previously saved values.

«
...
130
131
132
133
134
...
»

Summary of Contents for RGS Series




































































































































































































































































Reviews:

No comments

Related manuals for RGS Series

GuardSwitch 300 Series

Brand: GE Pages: 4

Brand: Magnetrol Pages: 12

Brand: Magnimage Pages: 53

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Brand: Jabra Pages: 4

Brand: Cabletron Systems Pages: 170

Brand: Manhattan Pages: 4

Brand: Cable Electronics Pages: 16

AV Selector 310

Brand: Hama Pages: 21

Brand: B&B Electronics Pages: 2

Brand: Black Box Pages: 2

Brand: Gefen Pages: 48

Brand: Holley Pages: 2

Sun Network QDR InfiniBand Gateway Switch

Brand: Oracle Pages: 96

Brand: TRENDnet Pages: 2

Brand: Longshine Pages: 26

Brand: Linkskey Pages: 2

Brand: H3C Pages: 44

Brand: IC Audio Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands