Zte ZXR10 8900 Series Hardware Installation Manual Download Page 78

Page: 78 / 109

ZXR10 8900 Series Hardware Installation Manual

IGURE

65 P

LUGGING

ARD

TEP

Plug-in Box

Card

Captive Screw

Result:

The card has been plugged.

Unplug a Card

To unplug a card, perform the following steps.

1. Loosen the captive screw on both sides of the card with a

screwdriver.

2. Press the card extractor with both hands. Turn the extractor

on both sides of the card outward. The card moves outward
when the connector is released.

3. Pull the card out along the guide rail.

Result:

The card has been unplugged.

Installation of Power Supply
Module

Installing Power Supply Module of
ZXR10 8912/8908/8905

ZXR10 8912, ZXR10 8908 and ZXR10 8905 use the same power
supply module. Here, take ZXR10 8908 for an example to intro-
duce how to install power supply module.

Confidential and Proprietary Information of ZTE CORPORATION

Summary of Contents for ZXR10 8900 Series














































































































Search results

Summary of Contents for ZXR10 8900 Series

Reviews:

Related manuals for ZXR10 8900 Series

Brands by name

Popular brands

Zte ZXR10 8900 Series, Hardware Installation Manual

Search results

Summary of Contents for ZXR10 8900 Series

Reviews:

Related manuals for ZXR10 8900 Series

Brands by name

Popular brands