background image

C h a p t e r

4

19” Standard Cabinet
Installation

Table of Contents

Bottom of Cabinet Installation .............................................17
Cabinet Installation............................................................37
Cabinet Accessories Remove and Installation.........................51

Bottom of Cabinet
Installation

Cabinet Position Rule

Layout of cabinets in one or more rows depends on size of equip-
ment room and quantity of cabinets. Layout of cabinets must com-
ply with the following requirements:

Distance between side of cabinets and the wall must be
≥900mm.

A path not less than 1m wide must be left within equipment
room.

Distance between the front of cabinet and the wall must be
≥1500mm.

Distance between fronts of one row of cabinet with front of
another row must be ≥1600mm.

Fixing cabinet mode must comply with room feature. There are
three installation methods, installing the cabinet on adjustable
base, installing the cabinet directly on floor and installing the
cabinet on fixed base.

The layout of cabinet must be convenient for installation, main-
tenance and system extension.

The arrangement of cabinet is decided by system configuration.
It must be designed with involvement of supplier’s technical
personnel and confirmed by the supplier.

Confidential and Proprietary Information of ZTE CORPORATION

17

Summary of Contents for ZXR10 8900 Series














































































































Reviews: