York YK Style H Operation Manual Download Page 87

Page: 87 / 212

Table 78: Programmable

Button

V09 software

and earlier

V10 and later

with YORK

Chiller Access

Manager

Description

Local Motor

Current Limit

Operator

Standard

Allows the user to specify the maximum allowed motor current (as a

percentage of FLA). When the motor current reaches this value, the Pre-

rotation Vanes will not be permitted to open further. If the motor current

rises above this value, the Pre-rotation Vanes will close to reduce the

current to this value.

Pulldown

Demand Limit Operator

Standard

Allows the user to specify the current limit value (as a percentage of FLA)

to which the chiller will be limited during the specified pulldown limit

time. This value will override the Motor Current Limit value during this

time period. This function is used to provide energy savings following

chiller start-up.

Pulldown

Demand Time Operator

Standard

Allows the user to set a period of time for which the pulldown demand

limit will be in effect after the chiller starts.

kWH Reset

Admin

Allows the user to reset the cumulative Kilowatt hours to zero (0).

Filter Inhibit

(Harmonic

Filter installed

Only)

Service

JCI Service

Disable the filter logic from activating, although the system will still

communicate with the device. Only available when chiller is stopped.

OptiSave

Service

JCI Service

Moves to a subscreen that displays OptiSave data, OptiSave calculates the

amount of energy a chiller with a VSD will save compared to a Constant

Speed chiller.

Motor Lube

View

Moves to the subscreen allowing operator acknowledgement of the

compressor motor lubrication and viewing of the compressor motor

lubrication parameters.

Table 79: Navigation

Button

V09 software

and earlier

V10 and later

with YORK

Chiller Access

Manager

Description

Home

View

Returns the user to Home Screen.

VSD Details

View

Navigates to the subscreen that provides more information about the

variable speed drive.

Motor Details

Service

JCI Service

Navigates to a subscreen that provides information and setpoints

pertinent to the Motor Monitoring feature.

Filter Details

(Harmonic

Filter installed

only)

View

Navigates to a subscreen that provides more information about the

harmonic filter.

Model YK Style H Centrifugal Liquid Chillers with OptiView Control Center

Summary of Contents for YK Style H





















































































































































































































Search results

Summary of Contents for YK Style H

Reviews:

Related manuals for YK Style H

Brands by name

Popular brands

York YK Style H, Operation Manual

Search results

Summary of Contents for YK Style H

Reviews:

Related manuals for YK Style H

Brands by name

Popular brands