York YK Style H Operation Manual Download Page 113

Page: 113 / 212

Table 108: Programmable

Button

V09 software

and earlier

V10 and later

with YORK

Chiller Access

Manager

Description

Winding Setup Service

JCI Service

Not shown when Winding Temperature Protection Setpoint on Motor

Details screen is set to Disabled. Allows a Service Technician to program

the High Winding Temperature (266°F to 320°F; default 311°F) and

Winding Hotspot Allowance (0°F to 18°F; default 0°F) safety shutdown

thresholds. Values entered are displayed in the respective data boxes.

Vibration Gain Admin

Admin

Only shown when access level is Admin and Motor Vibration Protection

Setpoint on Motor Details screen is not set to Disabled. Allows a Service

Technician to enter values for vibration Input Gain (1:1, 11:1, 21:1

[default]).

Bearing Setup Service

JCI Service

Not shown when Bearing Temperature Protection Setpoint on Motor

Details screen is set to Disabled. Allows a Service Technician to enter

values for High Bearing Temperature Shutdown (149°F to 212°F; default

203°F) and Warning (140°F to 194°F; default 194°F) thresholds.

Temperature

Disable

Admin

Only shown when access level is Admin and Winding Temperature

Protection Setpoint on Motor Details screen is not set to Disabled. Allows

a Service Technician to disable individual winding temperature sensors.

The respective temperature data box reflects enabled or disabled status.

This could be applied to defective sensors or for service reasons. When a

sensor is disabled, the respective temperature data box does not appear

on the Motor Details screen.

Table 109: Navigation

Button

V09 software

and earlier

V10 and later

with YORK

Chiller Access

Manager

Description

Home

Service

JCI Service

Returns the user to Home screen.

Motor Details

Service

JCI Service

Returns the user to Motor Details screen.

113

Model YK Style H Centrifugal Liquid Chillers with OptiView Control Center

Summary of Contents for YK Style H





















































































































































































































Search results

Summary of Contents for YK Style H

Reviews:

Related manuals for YK Style H

Brands by name

Popular brands

York YK Style H, Operation Manual

Search results

Summary of Contents for YK Style H

Reviews:

Related manuals for YK Style H

Brands by name

Popular brands