manualshive.com logo in svg

Yealink Yealink SIP-T42G, Administrator'S Manual

Share
Download
Yealink Yealink SIP-T42G Administrator'S Manual Download Page 85

Getting  Started

 

65

 

Details of Configuration Parameters:

 

Parameters 

Permitted Values 

Default 

network.internet_port.type 

0, 1 or 2 

0 

Description: 

Configures the Internet (WAN) port type for IPv4. 

0-DHCP 

1-PPPoE (not applicable to SIP-T42G/T41P/CP860 IP phones) 

2-Static IP Address 

Note: It works only if the value of the parameter “network.ip_address_mode” is set to 
0 (IPv4) or 2 (IPv4 & IPv6). If you change this parameter, the IP phone will reboot to 
make the change take effect. 

Web User Interface: 

Network->Basic->IPv4 Config 

Phone User Interface: 

Menu->Settings->Advanced Settings (default password: admin) ->Network->WAN 
Port->IPv4 

To configure DHCP via web user interface: 

1.

 

Click on Network->Basic. 

2.

 

In the IPv4 Config block, mark the DHCP radio box. 

 

3.

 

Click Confirm to accept the change. 

A dialog box pops up to prompt that settings will take effect after a reboot. 

4.

 

Click OK to reboot the phone. 

To configure DHCP via phone user interface: 

1.

 

Press Menu->Settings->Advanced Settings (default password: admin) 
->Network->WAN Port->IPv4. 

Summary of Contents for Yealink SIP-T42G



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands