Yealink Yealink SIP-T42G Administrator'S Manual Download Page 630

Page: 630 / 898

Administrator’s Guide for SIP-T2 Series/T19(P) E2/T4 Series/CP860 IP Phones

610

phone_setting.vq_rtcpxr_display_local_c
all_id.enable

phone_setting.vq_rtcpxr_display_remote
_call_id.enable

phone_setting.vq_rtcpxr_display_local_c
odec.enable

phone_setting.vq_rtcpxr_display_remote
_codec.enable

phone_setting.vq_rtcpxr_display_jitter.en
able

phone_setting.vq_rtcpxr_display_jitter_bu
ffer_max.enable

phone_setting.vq_rtcpxr_display_packets
_lost.enable

phone_setting.vq_rtcpxr_display_symm_
oneway_delay.enable

phone_setting.vq_rtcpxr_display_round_t
rip_delay.enable

phone_setting.vq_rtcpxr_display_moslq.e
nable

phone_setting.vq_rtcpxr_display_moscq.
enable

<MAC>.cfg

Configure the central report collector.

Parameters:

account.X.vq_rtcpxr.collector_name

account.X.vq_rtcpxr.collector_server_host

account.X.vq_rtcpxr.collector_server_port

Local

Web User Interface

Configure VQ-RTCPXR.

Configure the phone to display RTP status
showing the voice quality report of the
last call on the web user interface.

Configure the phone to display RTP status
showing the voice quality report of the
last call or the current call on the phone
user interface.

Configure the options of the RTP status
displayed on the phone user interface.

Navigate to:

http://<phoneIPAddress>/servlet?p=setti

Summary of Contents for Yealink SIP-T42G



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands

Yealink Yealink SIP-T42G, Administrator'S Manual

Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands