Yealink Yealink SIP-T42G Administrator'S Manual Download Page 659

Page: 659 / 898

Configuring Advanced Features

639

Click Confirm to accept the change.

Rport in

RFC 3581

, allows a client to request that the server sends the response back to

the source port from which the request came. Rport feature depends on support from a
SIP server.

Procedure

Rport feature can be configured using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure NAT Rport feature for
account.

Parameters:

account.X.nat.rport

Local

Web User Interface

Configure NAT Rport feature for
account.

Navigate to:

http://<phoneIPAddress>/servlet?p
=account-adv&q=load&acc=0

Details of Configuration Parameters:

Parameters

Permitted Values

Default

account.X.nat.rport

0, 1 or 2

Description:

Enables or disables NAT Rport feature for account X.

0-Disabled

1-Enabled

2-enable direct process

X ranges from 1 to 16 (for SIP-T48G/T46G/T29G)

X ranges from 1 to 12 (for SIP-T42G)

X ranges from 1 to 6 (for SIP-T41P/T27P)

X ranges from 1 to 3 (for SIP-T40P/T23P/T23G)

X ranges from 1 to 2 (for SIP-T21(P) E2)

X is equal to 1 (for SIP-T19(P) E2/CP860)

Web User Interface:

Account->Advanced->RPort

Summary of Contents for Yealink SIP-T42G



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands

Yealink Yealink SIP-T42G, Administrator'S Manual

Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands