Yealink Yealink SIP-T42G Administrator'S Manual Download Page 772

Page: 772 / 898

Administrator’s Guide for SIP-T2 Series/T19(P) E2/T4 Series/CP860 IP Phones

752

The system log level is set as 6, the informational level.

Note

Procedure

Log setting can be configured using the configuration files or locally.

Configuration File <y0000000000xx>.cfg

Configure the syslog mode.

Parameters:

syslog.mode

Local

Web User Interface

Configure the syslog mode.

Navigate to:

http://<phoneIPAddress>/servlet?m
=mod_data&p=settings-config&q=l
oad

Details of Configuration Parameters:

Parameters

Permitted Values

Default

syslog.mode

0, 1 or 2

Description:

Configures

the IP phone to export log files to the local system, syslog server or an

FTP/TFTP Server (provisioning server).

0-Local

1-Server

2-FTP/TFTP Server

Note: If you change this parameter, the IP phone will reboot to make the change
take effect.

Web User Interface:

Settings->Configuration->Export System Log

Phone User Interface:

None

Informational level

may make some sensitive information accessible (e.g., password

dial number), we recommend that you reset the system log level to 3 after providing the

syslog file.

Summary of Contents for Yealink SIP-T42G



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands

Yealink Yealink SIP-T42G, Administrator'S Manual

Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands