Yealink Yealink SIP-T42G Administrator'S Manual Download Page 120

Page: 120 / 898

Administrator’s Guide for SIP-T2 Series/T19(P) E2/T4 Series/CP860 IP Phones

100

Parameters

Permitted

Values

Default

Phone User Interface:

None

phone_setting.mute_power_led_flash_enable

0 or 1

Description:

Enables or disables the power indicator LED to flash when a call is muted.

For SIP-T48G/T46G/T42G/T41P/T40P/T29G/T27P/T23P/T23G/T21(P) E2 IP phones:

0-Disabled (power indicator LED does not flash)

1-Enabled (power indicator LED fast flashes (300ms) red)

For SIP-T19(P) E2 IP phones:

0-Disabled (power indicator LED does not flash)

1-Enabled (power indicator LED fast flashes (300ms) green)

Note: It is not applicable to CP860 IP phones.

Web User Interface:

Features->Power LED->Mute Power Light Flash

Phone User Interface:

None

phone_setting.hold_and_held_power_led_flash_enable

0 or 1

Description:

Enables or disables the power indicator LED to flash when a call is placed on hold or is
held.

For SIP-T48G/T46G/T42G/T41P/T40P/T29G/T27P/T23P/T23G/T21(P) E2 IP phones:

0-Disabled (power indicator LED does not flash)

1-Enabled ( power indicator LED fast flashes (500ms) red)

For SIP-T19(P) E2 IP phones:

0-Disabled (power indicator LED does not flash)

1-Enabled ( power indicator LED fast flashes (500ms) green)

Note: It is not applicable to CP860 IP phones.

Web User Interface:

Features->Power LED->Hold/Held Power Light Flash

Phone User Interface:

None

phone_setting.talk_and_dial_power_led_enable

0 or 1

Summary of Contents for Yealink SIP-T42G



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands

Yealink Yealink SIP-T42G, Administrator'S Manual

Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands