Yealink Yealink SIP-T42G Administrator'S Manual Download Page 695

Page: 695 / 898

Configuring Audio Features

675

Parameters

Permitted Values

Default

Note: It works only if the value of the parameter “voice.tone.country” is set to
Custom.

Web User Interface:

Settings->Tones->Dial

Phone User Interface:

None

voice.tone.ring

String

Blank

Description:

Customizes the ringback tone.

The value format is Freq/Duration. For more information on the value format, refer to
the parameter “voice.tone.dial”.

Note: It works only if the value of the parameter “voice.tone.country” is set to
Custom.

Web User Interface:

Settings->Tones->Ring Back

Phone User Interface:

None

voice.tone.busy

String

Blank

Description:

Customizes the tone when the callee is busy.

The value format is Freq/Duration. For more information on the value format, refer to
the parameter “voice.tone.dial”.

Note: It works only if the value of the parameter “voice.tone.country” is set to
Custom.

Web User Interface:

Settings->Tones->Busy

Phone User Interface:

None

voice.tone.congestion

String

Blank

Summary of Contents for Yealink SIP-T42G



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands

Yealink Yealink SIP-T42G, Administrator'S Manual

Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands