Yealink Yealink SIP-T42G Administrator'S Manual Download Page 414

Page: 414 / 898

Administrator’s Guide for SIP-T2 Series/T19(P) E2/T4 Series/CP860 IP Phones

394

Details of Configuration Parameters:

Parameters

Permitted Values

Default

features.play_local_dtmf_tone_enable

0 or 1

Description:

Enables or disables the IP phone to play a local DTMF tone.

0-Disabled

1-Enabled

If it is set to 1 (Enabled), you can hear the DTMF tone when pressing the IP phone’s
keypad during a call.

Web User Interface:

Features->General Information->Play Local DTMF Tone

Phone User Interface:

None

To configure play local DTMF tone via web user interface:

Click on Features->General Information.

Select the desired value from the pull-down list of Play Local DTMF Tone.

Click Confirm to accept the change.

You can mute the microphone of the active audio device during an active call, and then

Summary of Contents for Yealink SIP-T42G



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands

Yealink Yealink SIP-T42G, Administrator'S Manual

Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands