Yealink Yealink SIP-T42G Administrator'S Manual Download Page 213

Page: 213 / 898

Configuring Basic Features

193

Parameters

Permitted Values

Default

Features->General Information->Key As Send

Phone User Interface:

Menu->Features->Key as send

features.key_tone

0 or 1

Description:

Enables or disables the IP phone to play a key tone when a user presses any key

your phone keypad.

0-Disabled

1-Enabled

If it is set to 1 (Enabled), the IP phone will play a key tone when a user presses any
key

on your phone keypad.

Web User Interface:

Features->Audio->Key Tone

Phone User Interface:

Menu->Settings->Basic Settings->Sound->Key Tone

features.send_key_tone

0 or 1

Description:

Enables or disables the IP phone to play a key tone when a user presses a send key.

0-Disabled

1-Enabled

If it is set to 1 (Enabled), the IP phone will play a key tone when a user presses a
send key.

Note: It works only if the value of the parameter “features.key_tone” is set to 1
(Enabled).

Web User Interface:

Features->Audio->Send Tone

Phone User Interface:

None

To configure a send key via web user interface:

Click on Features->General Information.

Summary of Contents for Yealink SIP-T42G



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands

Yealink Yealink SIP-T42G, Administrator'S Manual

Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands