manualshive.com logo in svg

Yealink Yealink SIP-T42G, Administrator'S Manual

Share
Download
Yealink Yealink SIP-T42G Administrator'S Manual Download Page 103

Getting  Started

 

83

 

Half-duplex 

Half-duplex transmission refers to transmitting voice or data in both directions, but in 
one direction at a time; this means one device can send data on the line, but not 
receive data simultaneously. You can configure the half-duplex transmission on both 
Internet port and PC port for the IP phone to transmit in 10Mbps or 100Mbps. 

 

Full-duplex 

Full-duplex transmission refers to transmitting voice or data in both directions at the 
same time; this means one device can send data on the line while receiving data. You 
can configure the full-duplex transmission on both Internet port and PC port for the IP 
phone to transmit in 10Mbps, 100Mbps or 1000Mbps (1000Mbps is only applicable to 
SIP-T48G/T46G/T42G/T29G/T23G/CP860 IP phones). 

 

Procedure 

The transmission methods of Ethernet ports can be configured using the configuration 
files or locally. 

Configuration File  <y0000000000xx>.cfg 

Configure the transmission methods 
of the Internet (WAN) port. 

Parameters: 

network.internet_port.speed_duplex 

Summary of Contents for Yealink SIP-T42G



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands