Yealink Yealink SIP-T42G Administrator'S Manual Download Page 118

Page: 118 / 898

Administrator’s Guide for SIP-T2 Series/T19(P) E2/T4 Series/CP860 IP Phones

Talk/Dial Power Light On

Talk/Dial Power Light On allows the power indicator LED to be turned on when the IP
phone is busy.

Procedure

Power indicator LED can be configured using the configuration files or locally.

Configuration File

<y0000000000xx>.cfg

Configure the power indicator LED.

Parameters:

phone_setting.common_power_le
d_enable

phone_setting.ring_power_led_flas
h_enable

phone_setting.mail_power_led_fla
sh_enable

phone_setting.mute_power_led_fl
ash_enable

phone_setting.hold_and_held_po
wer_led_flash_enable

phone_setting.talk_and_dial_powe
r_led_enable

Local

Web User Interface

Configure the power indicator LED.

Navigate to:
http://<phoneIPAddress>/servlet?
p=features-powerled&q=load

Details of Configuration Parameters:

Parameters

Permitted

Values

Default

phone_setting.common_power_led_enable

0 or 1

Description:

Enables or disables the power indicator LED to be turned on.

For SIP-T48G/T46G/T42G/T41P/T40P/T29G/T27P/T23P/T23G/T21(P) E2 IP phones:

0-Disabled (power indicator LED is off)

1-Enabled (power indicator LED is solid red)

For SIP-T19(P) E2 IP phones:

0-Disabled (power indicator LED is off)

1-Enabled (power indicator LED is solid green)

Summary of Contents for Yealink SIP-T42G



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands

Yealink Yealink SIP-T42G, Administrator'S Manual

Search results

Summary of Contents for Yealink SIP-T42G

Reviews:

Brands by name

Popular brands