Yealink MeetingEye 400 Administrator'S Manual Download Page 4

Page: 4 / 278

| Contents |

Configuring DNS Server....................................................................................................................74
DHCP Options................................................................................................................................... 75

Supported DHCP Option of IPv4........................................................................................... 75
DHCP Option 42, Option 2.................................................................................................... 76
DHCP Option 12.....................................................................................................................76

Configuring LLDP.............................................................................................................................. 77

Configuring LLDP................................................................................................................... 77

Configuring VLAN Manually.............................................................................................................. 78
Configuring DHCP VLAN.................................................................................................................. 79
802.1x Authentication........................................................................................................................ 79

Configuring the 802.1x Authentication................................................................................... 80

Enabling/Disabling the PC Port.........................................................................................................81
Network Speed and Duplex Mode.................................................................................................... 82

Supported Transmission Methods.......................................................................................... 82
Configuring Transmission Methods........................................................................................ 82

Restricting Reserved Ports................................................................................................................83
Quality of Service (QoS)................................................................................................................... 84

Configuring QoS..................................................................................................................... 85

Configuring MTU............................................................................................................................... 86
Configuring SNMP.............................................................................................................................87

Configuring Account Settings..................................................................88

Setting SIP Account/SIP IP Call....................................................................................................... 88

Configuring SIP Accounts...................................................................................................... 89
Configuring SIP IP Call.......................................................................................................... 92

Setting H. 323 Account/H.323 IP Call.............................................................................................. 94

Configuring H.323 Accounts...................................................................................................94
H.323 Tunneling......................................................................................................................97

Configuring the PSTN account......................................................................................................... 98
Configuring the Video Conference Platform Account....................................................................... 99

Switching Platform Quickly..............................................................................................................115
Logging out of the Video Conference Platform...............................................................................115

Basic Settings.......................................................................................... 116

Setting Screen Saver for VP59....................................................................................................... 126

Summary of Contents for MeetingEye 400























































































































































































































































































Search results

Summary of Contents for MeetingEye 400

Reviews:

Yealink MeetingEye 400, Administrator'S Manual, Page: 4 / 278

Search results

Summary of Contents for MeetingEye 400

Reviews: