manualshive.com logo in svg

Yealink MeetingEye 400, Administrator'S Manual, Page: 82 / 278

Share
Download
Yealink MeetingEye 400 Administrator'S Manual Download Page 82

 | Configuring Network Settings | 

82

Network Speed and Duplex Mode

You can configure the network speed and duplex mode the system uses. The network speed and duplex
mode you select for the system must be supported by the switch.

VP59 allows you to configure the speed of Internet port and PC port.

•

Supported Transmission Methods

•

Configuring Transmission Methods

Supported Transmission Methods

The supported transmission methods for MeetingEye 600/MeetingEye 400/VC880/VC800/VC500/PVT980/
PVT950 are listed below:

• Auto
• Full Duplex (transmit in 10Mbps, 100Mbps or 1000Mbps)
• Half Duplex (transmit in 10Mbps or 100Mbps)

The supported transmission methods for VC200 are listed below:

• Auto
• Full Duplex (transmit in 10Mbps or 100Mbps)
• Half Duplex (transmit in 10Mbps or 100Mbps)

The supported transmission methods for VP59 are listed below:

•

WAN Port Link

• Auto Negotiation
• Full Duplex (transmit in 10Mbps, 100Mbps or 1000Mbps)
• Half Duplex (transmit in 10Mbps or 100Mbps)

•

PC Port Link

• Auto Negotiation
• Full Duplex (transmit in 10Mbps, 100Mbps or 1000Mbps)
• Half Duplex (transmit in 10Mbps or 100Mbps)

Configuring Transmission Methods

Procedure

1.

On your web user interface, go to 

Network

 > 

Advanced

 > 

Port Link

.

For VP59, on your web user interface, go to 

Network

 > 

Advanced

 > 

Port Link

.

2.

Configure and save the following settings:

Summary of Contents for MeetingEye 400























































































































































































































































































Reviews:

No comments