Yealink MeetingEye 400 Administrator'S Manual Download Page 91

Page: 91 / 278

| Configuring Account Settings |

Parameter

Description

Configuration Method

Transport

Specify the transport protocol
for transmitting the SIP
signaling.

The supported protocols are
as follows:

•

UDP

—it provides the

best transmission for SIP
signaling.

•

TCP

—it provides a reliable

transmission for SIP
signaling.

•

TLS

—it provides a safe

transmission for SIP
signaling. TLS is available
only when the device is
registered on a SIP server
that supports TLS.

• DNS-NAPTR—the device

performs the DNS NAPTR
and SRV request to find
the service type and the
port if no server port is
given.

Default

: UDP.

Web user interface

Endpoint

CTP20

Server Expires

The registration timeout (in
seconds) of the device.

After the timeout, the device
will send the registration
request to the SIP server
again.

Default

: 3600 seconds.

Web user interface

Endpoint

CTP20

Keep Alive Interval

Configure the interval (in
seconds) that the device
sends keep-alive messages
to the SIP server, so that
the SIP server can remain
connected to the device.

Default

: 30 seconds.

Web user interface

Summary of Contents for MeetingEye 400























































































































































































































































































Search results

Summary of Contents for MeetingEye 400

Reviews:

Brands by name

Popular brands

Yealink MeetingEye 400, Administrator'S Manual

Search results

Summary of Contents for MeetingEye 400

Reviews:

Brands by name

Popular brands