manualshive.com logo in svg

YASKAWA E-V-MD Series, User Manual

Share
Download
YASKAWA E-V-MD Series User Manual Download Page 210

8.8  Additional Adjustment Function

8-77

8

Adjustments

8.8

Additional Adjustment Function

This section describes the functions that can be used for additional fine tuning after making adjustments with 

advanced autotuning, advanced autotuning by reference, or one-parameter tuning.

• Switching gain settings
• Friction compensation
• Current control mode selection
• Current gain level setting
• Speed detection method selection

8.8.1

Switching Gain Settings

Two gain switching functions are available, manual switching and automatic switching. The manual switching 
function uses an external input signal to switch gains, and the automatic switching function switches gains 

automatically.

By using the gain switching function, the positioning time can be shortened by increasing the gain during posi-
tioning and vibration can be suppressed by decreasing the gain while it is stopped.

Note: n.



1 is reserved. Do not use.

For the gain combinations for switching, refer to 

(1)  Gain Combinations for Switching

.

For the manual gain switching, refer to 

(2)  Manual Gain Switching

.

For the automatic gain switching, refer to 

(3)  Automatic Gain Switching

.

(1) Gain Combinations for Switching

∗

The switching gain settings for the model following control gain and the model following control gain compensation 
are available only for manual gain switching. To enable the gain switching of these parameters, a gain switching input 
signal must be sent, and the following conditions must be met. 

•

No command being executed.

•

Motor having been completely stopped.

If these conditions are not satisfied, the applicable parameters will not be switched although the other parameters 

shown in this table will be switched.

(2) Manual Gain Switching

Manual gain switching uses G-SEL of the servo command output signals (SVCMD_IO) to switch between 
gain setting 1 and gain setting 2.

Parameter

Function

When Enabled

Classification

Pn139

n.



0

[Factory setting]

Manual gain switching 

Immediately

Tuning

n.



2

Automatic gain switching

Setting

Speed 

Loop 

Gain

Speed Loop 

Integral 

Time 

Constant

Position 

Loop Gain

Torque 

Reference 

Filter

Model 

Following 

Control Gain

Model 

Following 

Control Gain 

Compensation

Friction 

Compens

ation Gain

Gain 

Setting 1

PnAC2
Speed 
Loop 
Gain

PnAC4
Speed Loop 
Integral Time 
Constant

PnAC6
Position 
Loop Gain

Pn401 
Torque Refer-
ence Filter 
Time Constant

Pn141

*

Model Fol-
lowing Con-
trol Gain 

Pn142

*

Model Follow-
ing Control Gain 
Compensation

Pn121
Friction 
Compensa-
tion Gain

Gain 

Setting 2

Pn104
2nd Speed 
Loop 
Gain

Pn105

2nd Speed 
Loop Inte-
gral Time 
Constant

Pn106
2nd Position 
Loop Gain

Pn412 

1st Step 2nd 
Torque Refer-
ence Filter 
Time Constant

Pn148

*

2nd Model 
Following 
Control Gain

Pn149

*

2nd Model Fol-
lowing Control 
Gain Compensa-
tion

Pn122
2nd Gain 
for Friction 
Compensa-

tion

Type

Command Name

Setting

Meaning

Input

G-SEL of the servo command output 
signals (SVCMD_IO)

0

Switches to gain setting 1.

1

Switches to gain setting 2.

Summary of Contents for E-V-MD Series


































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands