Yamaha BRUIN 350 Owner'S Manual Download | Manualshive

Page: 76 / 174

background image

7-10

WARNING

_

Indicates a potential hazard that could
result in serious injury or death.

Do not operate at speeds too fast for your
skills or the conditions.

Speed limiter

For riders less experienced with this model,
this model is equipped with a speed limiter in
the throttle lever housing. The speed limiter
keeps the throttle from fully opening, even
when the throttle lever is pushed to the maxi-
mum. Turning the adjusting screw in limits the
maximum engine power available and de-
creases the maximum speed of the ATV.
Turning the adjusting screw in decreases top
speed and turning it out increases top speed.

1. Locknut

2. Adjusting screw

WARNING

POTENTIAL HAZARD
Operating this ATV at speeds too fast
for your skills or the conditions.
WHAT CAN HAPPEN
Increases your chances of losing con-
trol of the ATV, which can result in an
accident.
HOW TO AVOID THE HAZARD
Always go at a speed that is proper for
the terrain, visibility and operating con-
ditions, and your experience.

U5UH10.book Page 10 Monday, July 28, 2003 5:15 PM

«
...
74
75
76
77
78
...
»

Summary of Contents for BRUIN 350















































































































































































Reviews:

No comments

Related manuals for BRUIN 350

Brand: MANCO Pages: 4

FourTrax Foreman Rubicon TRX500FA5 2019

Brand: Honda Pages: 291

GRIZZLY 700 2014

Brand: Yamaha Pages: 176

Brand: Yamaha Pages: 174

Brand: Yamaha Pages: 46

Brand: Yamaha Pages: 155

Brand: Yamaha Pages: 190

Brand: Blaw-Knox Pages: 118

Brand: X-TREME Pages: 26

Brand: X-TREME Pages: 25

Brand: PRONAR Pages: 147

Brand: Humbaur Pages: 56

Brand: U-Line Pages: 9

Sasquatch Youth 800W

Brand: Daymak Pages: 24

Brand: Yamaha Pages: 141

Brand: Baja motorsports Pages: 82

Brand: Yamaha Pages: 288

Stampede 900 2017

Brand: Textron Pages: 237

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands