Yamaha BRUIN 350 Owner'S Manual Download

Page: 137 / 174

8-30

EBU11870

Front brake lever free play

The front brake lever should have a free play
of zero mm (zero in) at the lever end. If not,
have a Yamaha dealer check the brake sys-
tem.

a. Front brake lever free play

WARNING

POTENTIAL HAZARD
Operating with improperly serviced or
adjusted brakes.
WHAT CAN HAPPEN
You could lose braking ability, which
could lead to an accident.
HOW TO AVOID THE HAZARD
After servicing:

●

Make sure the brakes operate
smoothly and that the free play is
correct.

●

Make sure the brakes do not drag.

●

Make sure the brakes are not
spongy. All air must be bled from
the brake system.

Replacement of brake components re-
quires professional knowledge. These
procedures should be performed by a
Yamaha dealer.

U5UH10.book Page 30 Monday, July 28, 2003 5:15 PM

Summary of Contents for BRUIN 350















































































































































































Search results

Summary of Contents for BRUIN 350

Reviews:

Related manuals for BRUIN 350

Brands by name

Popular brands

Yamaha BRUIN 350, Owner'S Manual

Search results

Summary of Contents for BRUIN 350

Reviews:

Related manuals for BRUIN 350

Brands by name

Popular brands