Yamaha BRUIN 350 Owner'S Manual Download | Manualshive

Page: 75 / 174

background image

7-9

Pre-operation checks

Always perform the pre-operation checks list-
ed on page 5-1 before riding for safety and
proper care of the ATV.

WARNING

POTENTIAL HAZARD
Failure to inspect the ATV before oper-
ating.
Failure to properly maintain the ATV.
WHAT CAN HAPPEN
Increases the possibility of an accident
or equipment damage.
HOW TO AVOID THE HAZARD
Always inspect your ATV each time you
use it to make sure the ATV is in safe op-
erating condition. Always follow the in-
spection and maintenance procedures
and schedules described in the Owner’s
Manual.

WARNING

POTENTIAL HAZARD
Operating this ATV with improper tires,
or with improper or uneven tire pres-
sure.
WHAT CAN HAPPEN
Use of improper tires on this ATV, or op-
eration of this ATV with improper or un-
even tire pressure, may cause loss of
control, increasing your risk of an acci-
dent.
HOW TO AVOID THE HAZARD
Always use the size and type tires spec-
ified in the Owner’s Manual for this vehi-
cle on pages 5-8–5-9. Always maintain
proper tire pressure as described in the
Owner’s Manual on page 5-10.

U5UH10.book Page 9 Monday, July 28, 2003 5:15 PM

«
...
73
74
75
76
77
...
»

Summary of Contents for BRUIN 350















































































































































































Reviews:

No comments

Related manuals for BRUIN 350

Brand: ODES Pages: 136

Brand: Baltmotors Pages: 58

Brand: B&P Manufacturing Pages: 6

Brand: Taylor-Dunn Pages: 186

Brand: Taylor-Dunn Pages: 240

Brand: FLEMING Pages: 6

Brand: Dinli Pages: 122

Adapt-X Optimax

Brand: Apogee Pages: 24

Brand: Mi-T-M Pages: 65

Brand: Jayco Pages: 124

Brand: Panoz Pages: 67

Brand: GAS GAS Pages: 60

Brand: Kayo Pages: 4

Brand: Taylor-Dunn Pages: 162

Brand: Kipor Pages: 102

Brand: Bennche Pages: 181

Brand: Suzuki Pages: 136

Brand: Taylor-Dunn Pages: 246

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands