manualshive.com logo in svg

Yamaha BRUIN 350, Owner'S Manual

Share
Download
Yamaha BRUIN 350 Owner'S Manual Download Page 73

7-7

Apparel 

WARNING

POTENTIAL HAZARD 
Operating this ATV without wearing an
approved motorcycle helmet, eye pro-
tection and protective clothing. 
WHAT CAN HAPPEN 
Operating without
an approved motor-
cycle helmet in-
creases your
chances of a severe
head injury or death
in the event of an
accident. 
Operating without eye protection can re-
sult in an accident and increases your
chances of a severe injury in the event
of an accident. 

Operating without protective clothing
increases your chances of severe injury
in the event of an accident. 
HOW TO AVOID THE HAZARD 
Always wear an approved motorcycle
helmet that fits properly. 
You should also wear: 

eye protection 

(goggles or face shield) 

gloves 
boots 
long-sleeved shirt or jacket 
long pants

U5UH10.book  Page 7  Monday, July 28, 2003  5:15 PM

Summary of Contents for BRUIN 350















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands