Yamaha BRUIN 350 Owner'S Manual Download

Page: 26 / 174

4-4

EBU00733

Oil temperature warning light checking method

ACB-10E

Turn the main switch to “ON” and the
engine stop switch to “

”.

Oil temperature warning
light does not come on.

Oil temperature warning
light comes on.

Check engine oil temperature.

Oil temperature warning
light does not come on.

Engine oil temperature and
electrical circuit are OK. Go
ahead with riding.

Push start switch with the
transmission in neutral.

Ask a Yamaha dealer to
inspect the electrical circuit.

Oil tempera-
ture is low.

Allow to cool.

Oil tempera-
ture is high.

Oil temperature
warning light comes
on momentarily.

U5UH10.book Page 4 Monday, July 28, 2003 5:15 PM

Summary of Contents for BRUIN 350















































































































































































Search results

Summary of Contents for BRUIN 350

Reviews:

Related manuals for BRUIN 350

Brands by name

Popular brands

Yamaha BRUIN 350, Owner'S Manual

Search results

Summary of Contents for BRUIN 350

Reviews:

Related manuals for BRUIN 350

Brands by name

Popular brands