Yamaha BRUIN 350 Owner'S Manual Download | Manualshive

Page: 18 / 174

background image

2-5

WARNING

POTENTIAL HAZARD
Improper handling of gasoline.
WHAT CAN HAPPEN
Gasoline can catch fire and you could
be burned.
HOW TO AVOID THE HAZARD
Always turn off the engine when refuel-
ing.
Do not refuel immediately after the en-
gine has been running and is still very
hot.
Do not spill gasoline on the engine or
exhaust pipe/muffler when refueling.
Never refuel while smoking, or in the vi-
cinity of sparks, open flames, or other
sources of ignition such as the pilot
lights of water heaters and clothes dry-
ers.

When transporting the ATV in another
vehicle, be sure it is kept upright and
that the fuel cock is in the “OFF” posi-
tion. Otherwise, fuel may leak out of the
carburetor or fuel tank.
WHAT CAN HAPPEN
Gasoline is poisonous and can cause
injuries.
HOW TO AVOID THE HAZARD
If you should swallow some gasoline or
inhale a lot of gasoline vapor, or get
some gasoline in your eyes, see your
doctor immediately.
If gasoline spills on your skin, wash with
soap and water. If gasoline spills on
your clothing, change your clothes.

U5UH10.book Page 5 Monday, July 28, 2003 5:15 PM

«
...
16
17
18
19
20
...
»

Summary of Contents for BRUIN 350















































































































































































Reviews:

No comments

Related manuals for BRUIN 350

Brand: Yerf-Dog Pages: 21

BOSS RT FATBOY 1026RT RR

Brand: Meyer Pages: 44

Brand: Linhai Pages: 93

1970 SKI-DADDLER

Brand: AMF Pages: 74

Brand: CAMSO Pages: 50

Brand: Whirlwind Pages: 7

Brand: IBOTECH Pages: 60

Brand: HYOSUNG Pages: 48

Brand: Yamaha Pages: 213

Brand: Yamaha Pages: 282

Brand: Yamaha Pages: 443

Brand: Canyon Pages: 83

Brand: Can-Am Pages: 140

Brand: LONCIN Pages: 56

Brand: Tomberlin Pages: 151

1990 Electric Shuttle

Brand: Columbia Pages: 112

Brand: Carrier Pages: 315

Brand: E-Z-GO Pages: 135

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands