Yamaha BRUIN 350 Owner'S Manual Download | Manualshive

Page: 25 / 174

background image

4-3

EBU00605

Four-wheel-drive indicator light “ ”

This indicator light comes on when the 2WD/
4WD switch is in the 4WD position.

NOTE:

Due to the synchronizing mechanism in the
differential gear case, the light may not come
on until the ATV starts moving.

EBU11400

Oil temperature warning light “

”

When the oil temperature reaches a specified
level, this light comes on to warn that the en-
gine oil temperature is too hot. If the light
comes on during operation, stop the engine
as soon as it is safe to do so and allow the en-
gine to cool down for about 10 minutes.

CAUTION:

_

●

The engine may overheat if the ATV is
overloaded. If this happens, reduce
the load to specification.

●

Restart after making sure that the light
is out. Continuous use while the light
is on may cause damage to the en-
gine.

_

U5UH10.book Page 3 Monday, July 28, 2003 5:15 PM

«
...
23
24
25
26
27
...
»

Summary of Contents for BRUIN 350















































































































































































Reviews:

No comments

Related manuals for BRUIN 350

Brand: Taylor-Dunn Pages: 126

Brand: E-Z-GO Pages: 212

Brand: Wilson Electronics Pages: 3

Off Road Utility Vehicle 4430

Brand: Bush Hog Pages: 82

Sportsman 850 2021

Brand: Polaris Pages: 180

OneStopGardens 91240

Brand: Harbor Freight Tools Pages: 7

2009 Ranger RZR 800 EFI

Brand: Polaris Pages: 332

Brand: Jacobsen Pages: 60

Brand: Yamaha Pages: 141

Brand: Primo Water Pages: 12

Brand: Range Road Pages: 6

Brand: Polaris Pages: 4

Brand: CYBEX gold Pages: 52

Brand: Honda Pages: 298

Brand: American Sportworks Pages: 135

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands