Yamaha BRUIN 350 Owner'S Manual Download

Page: 50 / 174

5-8

EBU00157

Tires

WARNING

POTENTIAL HAZARD

Operating this ATV with improper tires,
or with improper or uneven tire pres-
sure.

WHAT CAN HAPPEN

Use of improper tires on this ATV, or op-
eration of this ATV with improper or un-
even tire pressure, may cause loss of
control, increasing your risk of acci-
dent.

HOW TO AVOID THE HAZARD

1. The tires listed below have been ap-

proved by Yamaha Motor Co., Ltd.
for this model. Other tire combina-
tions are not recommended.

ACE-01E

Manufacturer

Size

Type

Front

MAXXIS

AT25

8-12

M911Y

Rear

MAXXIS

AT25

10-12

M912Y

2. The tires should be set to the rec-

ommended pressure:

●

Recommended tire pressure

Front 25 kPa (0.25 kgf/cm

, 3.6 psi)

Rear 25 kPa (0.25 kgf/cm

, 3.6 psi)

●

Check and adjust tire pressures when
the tires are cold.

●

Tire pressures must be equal on both
sides.

3. Tire pressure below the minimum

specified could cause the tire to
dislodge from the rim under severe
riding conditions.
The following are minimums:

Front 22 kPa (0.22 kgf/cm

, 3.2 psi)

Rear 22 kPa (0.22 kgf/cm

, 3.2 psi)

U5UH10.book Page 8 Monday, July 28, 2003 5:15 PM

Summary of Contents for BRUIN 350















































































































































































Search results

Summary of Contents for BRUIN 350

Reviews:

Related manuals for BRUIN 350

Brands by name

Popular brands

Yamaha BRUIN 350, Owner'S Manual

Search results

Summary of Contents for BRUIN 350

Reviews:

Related manuals for BRUIN 350

Brands by name

Popular brands