Yamaha BRUIN 350 Owner'S Manual Download | Manualshive

Page: 157 / 174

background image

9-3

EBU00530

B. STORAGE

Long term storage (60 days or more) of your
machine will require some preventive proce-
dures to guard against deterioration. After
thoroughly cleaning the machine, prepare for
storage as follows:

1. Fill the fuel tank with fresh fuel and add

the specified amount of Yamaha Fuel
Stabilizer and Conditioner or an equiva-
lent product.

NOTE:

Use of fuel stabilizer and conditioner elimi-
nates the need to drain the fuel system. Con-
sult a Yamaha dealer if the fuel system needs
to be drained instead.

2. Remove the spark plug, pour about one

tablespoon of SAE 10W30 or 20W40
motor oil in the spark plug hole and rein-
stall the spark plug. Ground the spark
plug wire and turn the engine over seve-
ral times to coat the cylinder wall with oil.

3. Lubricate all control cables.
4. Block up the frame to raise all wheels off

the ground.

5. Tie a plastic bag over the exhaust pipe

outlet to prevent moisture from entering.

6. If storing in a humid or salt-air atmo-

sphere, coat all exposed metal surfaces
with a light film of oil. Do not apply oil to
any rubber parts or the seat cover.

Specified amount:

1 oz of stabilizer to each gallon of fuel
(or 7.5 cc of stabilizer to each liter of
fuel)

U5UH10.book Page 3 Monday, July 28, 2003 5:15 PM

«
...
155
156
157
158
159
...
»

Summary of Contents for BRUIN 350















































































































































































Reviews:

No comments

Related manuals for BRUIN 350

Brand: KAYO MOTO Pages: 9

Brand: MANCO Pages: 4

Brand: Yerf-Dog Pages: 59

Brand: Suzuki Pages: 382

Brand: GMX MOTORBIKES Pages: 57

Transicold X4 7300

Brand: Carrier Pages: 282

Brand: Jayco Pages: 124

Brand: Yamaha Pages: 140

Brand: Zap Pages: 27

Brand: U-Line Pages: 8

Brand: MULTIQUIP Pages: 54

Brand: Yamaha Pages: 288

Brand: Westbrook Trailers Pages: 34

Challenger4 300

Brand: TrailMaster Pages: 15

Brand: TrailMax Pages: 58

Brand: TrailMax Pages: 75

Brand: TrailMax Pages: 76

Brand: Arctic Cat Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands