Yamaha BRUIN 350 Owner'S Manual Download

Page: 154 / 174

8-47

EBU04400

Troubleshooting chart

1. Fuel

Check if there is fuel
in the fuel tank.

There is fuel.

Turn the fuel cock
lever to “OFF”.

No fuel.

Fuel cock is
clogged.

Clean the
fuel cock.

Some fuel.

Turn the fuel cock
lever to “RES”.

Restart the engine.

No fuel.

Supply fuel.

2. Compression

Use the electric
starter to see if
there is compression.

There is compression.

Compression normal.

No compression.

Ask a Yamaha dealer to
inspect.

3. Ignition

Remove the
spark plug and
check electrodes.

Wet

Wipe clean with dry cloth.

Dry

Attach spark plug cap and
ground to chassis.

Use the
electric starter.

Spark is good.

Ignition system is
normal.

Spark is weak.

Adjust the spark plug gap
or replace the spark plug.

No spark.

Ask a Yamaha dealer to
inspect.

4. Battery

Use the electric starter.

Engine turns over
quickly.

Battery is good.

Engine turns over
slowly.

Check the connections.

Check the
fuel flow.

Turn the fuel cock
lever to “ON”.

Remove the fuel hose
from the fuel cock.

U5UH10.book Page 47 Monday, July 28, 2003 5:15 PM

Summary of Contents for BRUIN 350















































































































































































Search results

Summary of Contents for BRUIN 350

Reviews:

Related manuals for BRUIN 350

Brands by name

Popular brands

Yamaha BRUIN 350, Owner'S Manual

Search results

Summary of Contents for BRUIN 350

Reviews:

Related manuals for BRUIN 350

Brands by name

Popular brands