Yamaha BRUIN 350 Owner'S Manual Download | Manualshive

Page: 122 / 174

background image

8-15

5. Fill the differential gear case with the

specified amount of the recommended
oil.

NOTE:

_

●

Do not exceed the specified differential
gear oil quantity when filling. Overfilling
will cause the oil to seep out of the
breather hose during and after riding.

●

The differential gear oil level cannot be
checked. The differential gear case ca-
pacity is greater than the recommended
oil quantity, therefore the oil level cannot
be accurately checked from the oil filler
cap hole.

_

CAUTION:

_

Be sure no foreign material enters the dif-
ferential gear case.

_

6. Install the oil filler bolt.
7. Check for oil leakage. If oil leakage is

found, check for the cause.

Recommended oil:

SAE 80 API “GL-4” Hypoid gear oil

Oil quantity:

0.35 L (0.31 Imp qt, 0.37 US qt)

U5UH10.book Page 15 Monday, July 28, 2003 5:15 PM

«
...
120
121
122
123
124
...
»

Summary of Contents for BRUIN 350















































































































































































Reviews:

No comments

Related manuals for BRUIN 350

Brand: Taylor-Dunn Pages: 192

Brand: Ardisam Pages: 8

Brand: Dinli Pages: 99

GROUND FORCE ELITE

Brand: Razor Pages: 16

Brand: Arctic Cat Pages: 174

Brand: Panther Pages: 16

Brand: Can-Am Pages: 152

Renegade 1000R 2016

Brand: Can-Am Pages: 534

Brand: PRONAR Pages: 101

Sportsman 850 XP

Brand: Polaris Pages: 148

Brand: PAXSTER Pages: 24

Brand: Tao Motor Pages: 69

Brand: TAO Pages: 76

Brand: Jayco Pages: 100

Brand: Yamaha Pages: 184

Brand: Yamaha Pages: 141

Brand: Yamaha Pages: 180

Brand: Taylor-Dunn Pages: 240

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands