Yamaha BRUIN 350 Owner'S Manual Download | Manualshive

Page: 81 / 174

background image

7-15

Exhaust system

The exhaust system on the ATV is very hot
during and following operation. To prevent
burns, avoid touching the exhaust system.
Park the ATV in a place where pedestrians or
children are not likely to touch it.

WARNING

POTENTIAL HAZARD
Hot exhaust system.
WHAT CAN HAPPEN
Dry grass or brush or other combustible
material accumulated around the en-
gine area could catch fire.
Someone touching the exhaust system
during or after operation could be
burned.
HOW TO AVOID THE HAZARD
Do not operate, idle, or park the ATV in
dry grass or other dry ground cover.
Keep the engine area free of dry grass,
brush, or other combustible material.

Do not touch the hot exhaust system.
Do not park the ATV in a place where
others might be likely to touch it.

U5UH10.book Page 15 Monday, July 28, 2003 5:15 PM

«
...
79
80
81
82
83
...
»

Summary of Contents for BRUIN 350















































































































































































Reviews:

No comments

Related manuals for BRUIN 350

Brand: Bajaj Motorsport Pages: 8

Brand: Bad Boy Pages: 56

Brand: Baja motorsports Pages: 76

Superlift Advantage Operators

Brand: Genie Pages: 28

Brand: HTI Pages: 6

Brand: X-TREME Pages: 26

2015 Cadillac Escalade

Brand: ACG Pages: 15

IBT 4000 Series

Brand: IBEA Pages: 56

Brand: Taylor-Dunn Pages: 162

Brand: Ifor Williams Trailers Pages: 55

Sasquatch Youth 800W

Brand: Daymak Pages: 24

Brand: Yamaha Pages: 32

GRIZZLY 350 2016

Brand: Yamaha Pages: 140

Warrior YFM350XRC

Brand: Yamaha Pages: 174

Brand: Yamaha Pages: 166

Brand: Yamaha Pages: 150

GRIZZLY YFM70GPAL

Brand: Yamaha Pages: 182

Brand: Yamaha Pages: 287

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands