Yamaha BRUIN 350 Owner'S Manual Download | Manualshive

Page: 31 / 174

background image

4-9

EBU01159

Speed limiter

The speed limiter keeps the throttle from fully
opening, even when the throttle lever is
pushed to the maximum. Turning in the ad-
justing screw limits the maximum engine pow-
er available and decreases the maximum
speed of the ATV.

1. Locknut

2. Adjusting screw

a. 12 mm (0.47 in)

WARNING

POTENTIAL HAZARD
Improper adjustment of the speed limit-
er and throttle.
WHAT CAN HAPPEN
The throttle cable could be damaged.
Improper throttle operation could result.
You could lose control, have an acci-
dent or be injured.
HOW TO AVOID THE HAZARD
Do not turn the adjusting screw out
more than 12 mm (0.47 in). Always make
sure the throttle lever free play is adjust-
ed to 3–5 mm (0.12–0.20 in). See page
8-26.

U5UH10.book Page 9 Monday, July 28, 2003 5:15 PM

«
...
29
30
31
32
33
...
»

Summary of Contents for BRUIN 350















































































































































































Reviews:

No comments

Related manuals for BRUIN 350

Brand: Bajaj Motorsport Pages: 8

Brand: Yamaha Pages: 26

CU-48 OFF-ROAD SERIES

Brand: Crown Pages: 8

Brand: Komatsu Pages: 4

Brand: Tractor Supply Pages: 102

ESCALATE TRAILER ET 12000

Brand: Bil-Jax Pages: 20

Brand: Landa Pages: 14

Treker 700-109P

Brand: Land Pride Pages: 104

Brand: Yamaha Pages: 178

Brand: Yamaha Pages: 184

Brand: Yamaha Pages: 156

Brand: Yamaha Pages: 166

Workman HD Series

Brand: Toro Pages: 318

Brand: KAYO MOTO Pages: 8

Brand: Yamaha Pages: 188

Viking YXM70VPXH 2016

Brand: Yamaha Pages: 172

Trailer Tracks 150

Brand: Omnitracs Pages: 52

Challenger4 300

Brand: TrailMaster Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands