Yamaha BRUIN 350 Owner'S Manual Download | Manualshive

Page: 44 / 174

background image

5-2

EBU12521

Front and rear brakes
Brake levers and brake pedal

●

Check for correct free play in the front
brake lever. If the free play is incorrect,
have a Yamaha dealer adjust it.

●

Check for correct free play in the rear brake
lever and brake pedal. If the free play is in-
correct, adjust it. (See pages 8-31–8-33.)

●

Check operation of the levers and pedal.
They should move smoothly and there
should be a firm feeling when the brake is
applied. If not, have a Yamaha dealer in-
spect them.

Brake fluid level (front brake)

Check the brake fluid level. Add fluid if neces-
sary. (See pages 8-28–8-29.)

WARNING

POTENTIAL HAZARD

Failure to inspect the ATV before oper-
ating.
Failure to properly maintain the ATV.

WHAT CAN HAPPEN

Increases the possibility of an accident
or equipment damage.

HOW TO AVOID THE HAZARD

Always inspect your ATV each time you
use it to make sure the ATV is in safe op-
erating condition.
Always follow the inspection and main-
tenance procedures and schedules de-
scribed in the Owner’s Manual.

Recommended brake fluid: DOT 4

U5UH10.book Page 2 Monday, July 28, 2003 5:15 PM

«
...
42
43
44
45
46
...
»

Summary of Contents for BRUIN 350















































































































































































Reviews:

No comments

Related manuals for BRUIN 350

WOLVERINE YFM45FXV

Brand: Yamaha Pages: 34

BLASTER YFS200S

Brand: Yamaha Pages: 46

Brand: Yamaha Pages: 59

LYNX RADIEN UTILITY ACE 2022 Series

Brand: BRP Pages: 252

Sniper T-1500 2S

Brand: BMS Pages: 69

Adapt-X Optimax

Brand: Apogee Pages: 24

Brand: swaploader Pages: 94

Sportsman 9920775

Brand: Polaris Pages: 144

Turf Cat 628 ROPS

Brand: Jacobsen Pages: 9

Brand: E-Z-GO Pages: 134

Brand: Dane Technologies Pages: 74

Brand: Jayco Pages: 100

Brand: Parklands Pages: 101

Roadster RT-622 2010

Brand: Can-Am Pages: 52

Brand: Yamaha Pages: 156

Vector RS90LTGTZ

Brand: Yamaha Pages: 98

Can-Am Defender DPS HD10

Brand: BRP Pages: 244

BOMBARDIER DS250 2006

Brand: BRP Pages: 284

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands