Xyratex RS-1600-FC-SBD Installation And User Manual Download Page 22

Page: 22 / 82

RS-1600/1602-FC-SBD User Guide

Processors housed on the SBD modules provide enclosure management interfacing to devices on the
Backplane, PSU, SBD module and Ops Panel, to monitor internal functions.These processors operate in

a master slave configuration to allow failover.

The module incorporates the following LED indicators:

Host

LED Functions

LED State

Description

Host Port 0 Signal Good

Green

incoming FC signal GOOD

Host Port 1 Signal Good

Green

incoming FC signal GOOD

Host Port 2 Signal Good

Green

incoming FC signal GOOD

Host Port 3 Signal Good

Green

incoming FC signal GOOD

Status

Green

OFF

Flashing

All device ports GOOD @ 2Gb/s

All device ports GOOD @ 1Gb/s

Drives bypassed on module

SBD Module Fault

Amber

SBD module FAILED

Figure 1–8

SBD Module

Summary of Contents for RS-1600-FC-SBD



















































































Search results

Summary of Contents for RS-1600-FC-SBD

Reviews:

Related manuals for RS-1600-FC-SBD

Brands by name

Popular brands

Xyratex RS-1600-FC-SBD, Installation And User Manual

Search results

Summary of Contents for RS-1600-FC-SBD

Reviews:

Related manuals for RS-1600-FC-SBD

Brands by name

Popular brands