Xerox Versant 180 Press User Manual Download | Manualshive

Page: 139 / 166

background image

Suggested Solutions

Tip

Changing the default setting of 0 (zero) is a temporary solution because environmental
conditions vary from day to day. Upon completion of the print job, the recommendation
is to return the option to its default setting.

• Use this feature to adjust the fuser temperature.

• If dry ink / toner comes off the paper, especially with special media, resolve the problem

by increasing the fusing temperature.

• If the fuser temperature is too high when printing on lightweight paper, it may cause

blocking, media damage, or paper jams at the peeling unit in the fusing module.

• If the fuser temperature is too low, it may cause poor fusing on higher-density image

areas and toner may peel off the printed output.

• This feature is accessed from Machine Status > Tools > Setup & Adjustment > Custom

Paper Settings. Select the desired Custom Paper > Change Settings > Adjust Fuser
Temperature > Change Settings.

• Based on the printed output, increase or decrease the Adjust Fuser Temperature in

increments of 1° or 2°.

• After each incremental adjustment, run test prints and evaluate the output to determine

if additional adjustments are required.

2.

If feeding paper from trays 6-9 and if the paper is damp, confirm that the Tray Heater
feature is Enabled (checked).

Note

Tray Heater is available only for trays 6-9.

• Use this feature to Enable (checked) or Disable (unchecked) the tray heater.

• The tray heater warms the air that is blown into the tray by Adjust Air Assist Values

and helps prevent paper jams and multifeeds by loosening contact between sheets.

• The tray heater may partially dry paper and affect print quality. If print quality is affected

by dry paper, disable the tray heater.

Note

Disabling the tray heater may result in an increase of multifeeds.

• This feature is accessed from Machine Status > Tools > Setup & Adjustment > Custom

Paper Settings. Select the desired Custom Paper > Change Settings > Tray Heater >
Change Settings.

• To Enable (check) the box for Tray Heater.

6-17

Xerox

®

Versant

®

180 Press

User Guide

Troubleshooting

«
...
137
138
139
140
141
...
»

Summary of Contents for Versant 180 Press







































































































































































Reviews:

No comments

Related manuals for Versant 180 Press

image Prograf iPF785 Series

Brand: Canon Pages: 136

Brand: GBC Pages: 110

Color imageCLASS MF8580Cdw

Brand: Canon Pages: 750

ImageCLASS 2300

Brand: Canon Pages: 8

Color imageCLASS MF8580Cdw

Brand: Canon Pages: 750

Color imageCLASS 8180c

Brand: Canon Pages: 95

Brand: Canon Pages: 4

Brand: Canon Pages: 49

ImageCLASS 2300

Brand: Canon Pages: 156

Brand: Canon Pages: 193

Brand: QMS Pages: 24

imageCLASS D1120

Brand: Canon Pages: 36

ImageCLASS 2300

Brand: Canon Pages: 44

Brand: Canon Pages: 66

Brand: Oki Pages: 24

Brand: VAF instruments Pages: 24

Brand: GCC Technologies Pages: 63

Brand: GCC Technologies Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands