Xerox Versant 180 Press User Manual Download Page 134 | Manualshive

Page: 134 / 166

background image

Suggested Solutions

• The tray heater may partially dry paper and affect print quality. If print quality is affected

by dry paper, Disable the tray heater.

Note

Disabling the tray heater may result in an increase of multifeeds.

• This feature can be found in Machine Status > Tools > Setup & Adjustment > Custom

Paper Settings. Select the desired Custom Paper > Change Settings > Tray Heater >
Change Settings.

• To Disable (unchecked) the tray heater:

a.

Remove any paper loaded in the tray.

b.

In Adjust Air Assist Values select any option except Forced Off .

c.

Disable (unchecked ) the tray heater and register the stock.
The printer performs a forced exhaust action for approximately one minute. During
the forced exhaust action, do not change any settings or open a tray.

Important

A forced exhaust with paper loaded in tray can lead to image quality problems.

d.

After the forced exhaust is complete, load paper in tray.

3.

Change the Multifeed Detection setting.

• Use this feature to Enable (checked) or Disable (unchecked) multifeed notifications;

this feature does not make any other adjustments.

• The Multifeed Detection feature is accessed from Machine Status > Tools > Setup &

Adjustment > Custom Paper Settings. Select the desired Custom Paper > Change
Settings > Multifeed Detection > Change Settings.

• The settings available for the Multifeed Detection option include:

-

Enabled (checked): Multifeed notifications are switched On.

-

Disabled (unchecked): Multifeed notifications are switched Off.

Note

To prevent the system from reporting faults due to multifeeds, temporarily disable
notifications. This allows the user to continue their workflow until the cause of the
problem is resolved. Be aware that disabling this feature has no impact on the oc-
currence rate of actual multifeeds, and if disabled, multifed sheets may cause jams
elsewhere in the system and/or result in additional blank sheets in the final output.

Problem

Paper Curl

Suggested Solutions

1.

If your press configuration includes the Interface Decurler Module (IDM)s, confirm that
the IDM Curl Correction option on the IDM control panel is set to Auto.

Note

For more information, refer to the Optional Devices Guide for Xerox

®

Versant

®

180 Press,

the Interface Decurler Module (IDM) chapter.

Xerox

®

Versant

®

180 Press

6-12

User Guide

Troubleshooting

«
...
132
133
134
135
136
...
»

Summary of Contents for Versant 180 Press







































































































































































Reviews:

No comments

Related manuals for Versant 180 Press

image Prograf iPF785 Series

Brand: Canon Pages: 136

Brand: GBC Pages: 110

Pixma MG2400 Series

Brand: Canon Pages: 2

Brand: Datecs Pages: 29

Brand: TallyGenicom Pages: 145

T2265 SprintPro

Brand: Tally Pages: 217

Brand: TallyGenicom Pages: 12

Brand: Wasp Pages: 2

Brand: Canon Pages: 4

Brand: Oki Pages: 52

Brand: Konica Minolta Pages: 32

Brand: Roland Pages: 44

ECOSYS M6035cdn

Brand: Kyocera Pages: 31

Brand: IBM Pages: 16

1235/DX - Phaser Color Laser Printer

Brand: Xerox Pages: 144

M-Class Mark II M-4206

Brand: Datamax Pages: 76

Brand: Philips Pages: 56

AR M207 - B/W Laser - All-in-One

Brand: Sharp Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands