Xerox Versant 180 Press User Manual Download | Manualshive

Page: 116 / 166

background image

Note

After you replace a dry ink/toner cartridge, the system automatically resets the usuage
counter to zero (0) for this CRU. Check the Consumables Supplies screen to verify the
reset and new status.

1. Open the Dry Ink/Toner cover, located just above the press front door.

2. Lay paper on the floor before removing the cartridge. This will allow any excess dry

ink/toner to fall on the paper.

3. Grasp the handle of the dry ink/toner cartridge matching the color indicated in the

message.

4. Remove the dry ink/toner cartridge by slowly and gently pulling it straight out. While

pulling out, hold the bottom of the cartridge with your other hand to give it support.

5. Dispose of or recycle the cartridge per your local authorities and regulations.

In the United States, also refer to the Electronic Industries Alliance website:

. For more information about Xerox environmental programs, go to

www.xerox.com/environment

.

6. Remove the new dry ink/toner cartridge from its packaging.
7. With one hand on either side of the cartridge, vigorously shake and rotate the new

cartridge up and down and left and right for 30 seconds to redistribute the toner.

8. Install the new dry ink/toner cartridge by gently and evenly sliding the cartridge into

the press until it stops.

9. Close the dry ink/toner cover. If the cover does not close completely, make sure the

cartridge is in the lock position and is installed into the appropriate dry ink/toner
location.

Replacing the Dry Ink/Toner Waste Bottle

The Dry Ink/Toner Waste Bottle collects dry ink/toner that accumulates during the
printing process. When the bottle is full, a message displays on the press UI informing
you to exchange the full bottle with an empty one.

The press contains one waste bottle located at the front of the press behind the Dry
Ink/Toner Waste Bottle Door. When removing a full Dry Ink/Toner Waste bottle, SLOWLY
pull it out of the press. This will prevent any dry ink/toner from spilling out of the bottle.

Note

After you replace the Dry Ink/Toner Waste Bottle, the system automatically resets the
usage counter to zero (0) for this CRU component. Check the Consumables Supply screen
to verify the reset.

1. Ensure that the press is stopped (not running any jobs).

Xerox

®

Versant

®

180 Press

5-8

User Guide

Maintenance

«
...
114
115
116
117
118
...
»

Summary of Contents for Versant 180 Press







































































































































































Reviews:

No comments

Related manuals for Versant 180 Press

Brand: TallyGenicom Pages: 38

Brand: Lanier Pages: 265

Brand: Konica Minolta Pages: 32

Brand: Xerox Pages: 20

Brand: U-Line Pages: 33

Brand: Ricoh Pages: 17

Brand: Kyocera Pages: 2

Brand: IBM Pages: 4

Brand: Xerox Pages: 85

Brand: OmniPrint Pages: 23

Brand: Xerox Pages: 2

Brand: WOOSIM Pages: 19

Brand: Dell Pages: 128

Brand: Dell Pages: 4

Brand: Dell Pages: 4

3130cn - Color Laser Printer

Brand: Dell Pages: 4

Brand: Dell Pages: 4

Brand: Dell Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands