![background image](http://html2.mh-extra.com/html/xerox/phaser-6121mfp/phaser-6121mfp_service-manual_4154850133.webp)
Phaser 6121MFP Service Manual
3-27
Error Messages and Codes
008D
Receiver’s protocol of DIS is received, but remote side can not receive
documents temporarily. This can be caused by out of paper condition
or other reason.
008E
Remote side CSI number not defined in machine one touch or speed
dial directory.
008F
Modem not ready to receive V.34 data within 6 seconds after received
CFR signal.
0090
Called side document not ready for polling.
0091
Sending DCS+TCF signal 3 times consecutively but no signal in
response from receiver.
0092
Remote side disconnected within transmitting phase.
0093
Received DCN signal after sending out DCS signal for V.34.
0094
Time out during transmit ECM frame or RCP command.
0095
Wrong ID number when Polling RX.
0099
Remote side disconnect after primary channel.
009A
Cannot detect any signal after sending CI signal.
009C
Received DCN after sending DTC in V.34 polling RX.
009D
Remote side hang up before V.34 modem enter phase 2 state in V.34
polling RX.
009F
No response received from other side after sending PPS_EOM signal.
00A0
User stopped or canceled transmission job.
00A1
Document jam within transmission.
00AE
Cannot finish V.8 procedure or detect V.21 signal within 30 seconds
after CM signal.
OOAF
Modem can not enter into control channel after TX side sending RCP
signal for V.34.
00B0
No command received after resending DCS signal in V.34 TX.
00B1
Cannot finish V.8 procedure or detect V.21 signal within 35 seconds
after ANSam signal.
00B2
Cannot detect phase 2 signal within 30 seconds after sending CJ
signal.
00B3
Cannot detect correct V.21 or JM signal after sending CM signal.
00B4
Cannot detect correct phase 2 signal within 25 seconds after CM/JM
signal exchange.
00B5
Cannot detect phase 3 signal within 25 seconds after phase 2.
00B6
Cannot detect phase 4 signal within 25 seconds after CM/JM
exchange.
00B7
Cannot detect phase 5 signal within 30 seconds after phase 4.
00B8
Remote side disconnect after sending DCS signal in V.34.
00B9
Receive T.30 signal other than DIS, DCS, CFR after sending DCS signal
in V.34.
Code
Possible Causes of Error
Summary of Contents for PHASER 6121MFP
