Xerox DocuPrint C55 Supplementary Manual Download Page 189 | Manualshive

Page: 189 / 395

background image

U N I X 43

5.

If you suspect that the cause of the communications problem is
the DocuPrint printer, print out a Print Settings page at the
printer’s Control Panel and view the TCP/IP parameters.

6.

If Dynamic IP Addressing is enabled (DEFAULT) try “hard
coding” the DocuPrint printer IP address at the control panel.
Reset the printer, and check for connectivity again with the
“ping” command.

7.

If Dynamic IP Addressing is disabled, verify the following
settings on the Print Settings page with your local TCP/IP
address administrator. This person should be able to verify the
correctness of:

•

IP address

•

Subnet Mask

•

Default Gateway

Any one of these important TCP/IP parameters (if set incorrectly)
can cause TCP/IP communication problems. Subnet Mask and
Default Gateway are critical on multi-network segment
LAN/WAN’s. If you make any TCP/IP configuration changes,
then the DocuPrint printer must be reset for those changes to take
effect.

8.

If all of the above troubleshooting fails, you may have a
malfunctioning NIC. Try a Factory Reset at the DocuPrint
printer Control Panel. Manually set the IP address, Subnet mask,
and Default Gateway at the DocuPrint printer Control Panel.
Reset the printer. Try to ping the printer again. If the problem
persists, call Xerox Technical Support for further instructions.

«
...
187
188
189
190
191
...
»

Summary of Contents for DocuPrint C55












































































































































































































































































































































































































Reviews:

No comments

Related manuals for DocuPrint C55

Color imageCLASS MF8580Cdw

Brand: Canon Pages: 36

Color imageCLASS MF8580Cdw

Brand: Canon Pages: 20

Color imageCLASS MF8280Cw

Brand: Canon Pages: 24

Color imageCLASS MF8080Cw

Brand: Canon Pages: 39

Color imageCLASS MF8050Cn

Brand: Canon Pages: 32

Color imageCLASS LBP7660Cdn

Brand: Canon Pages: 2

Color imageCLASS 8180c

Brand: Canon Pages: 24

Brand: Canon Pages: 30

C3000 - MultiPASS Color Inkjet Printer

Brand: Canon Pages: 41

Color imageCLASS MF8170c

Brand: Canon Pages: 2

Color imageCLASS MF8170c

Brand: Canon Pages: 98

Color imageCLASS MF8170c

Brand: Canon Pages: 8

Color imageCLASS MF8080Cw

Brand: Canon Pages: 46

Color imageRUNNER LBP5360

Brand: Canon Pages: 3

Brand: Magicard Pages: 26

Brand: QMS Pages: 194

Brand: TallyGenicom Pages: 2

Brand: Canon Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands