Weinzierl KNX IO 534 (4D) Operation And Installation Manual Download Page 41

Page: 41 / 41

2019 WEINZIERL ENGINEERING GmbH

Page 41/41

Input on (1) is converted into output off (0). Input off (0) is con-
verted into output on (1).

Group Object

Type KNX

Size

Direction

Logic - Gate input - Input

1.002

1 Bit

From KNX

Logic - Gate output - Output

1.002

1 Bit

To KNX

WARNING



The device must be mounted and commissioned by
an authorized electrician.



The prevailing safety rules must be heeded.



The device must not be opened.



For planning and construction of electric installa-
tions, the relevant guidelines, regulations and
standards of the respective country are to be con-
sidered.



The power rating is indicated on the side of the
product.

ETS4/5 Database

www.weinzierl.de/en/products/534/ets4

Datasheet

www.weinzierl.de/en/products/534/datasheet

CE Declaration

www.weinzierl.de/en/products/534/ce-declaration

Weinzierl Engineering GmbH

D-84508 Burgkirchen / Alz

Germany

www.weinzierl.de

[email protected]

2019/03/05

Summary of Contents for KNX IO 534 (4D)










































Search results

Summary of Contents for KNX IO 534 (4D)

Reviews:

Related manuals for KNX IO 534 (4D)

Brands by name

Popular brands

Weinzierl KNX IO 534 (4D), Operation And Installation Manual

Search results

Summary of Contents for KNX IO 534 (4D)

Reviews:

Related manuals for KNX IO 534 (4D)

Brands by name

Popular brands