manualshive.com logo in svg

Waygate Technologies Krautkramer USM 10, Operating Manual

Share
Download
Waygate Technologies Krautkramer USM 10 Operating Manual Download Page 141

Evaluation

5  Operation

Krautkrämer USM 100

Rev. - (09/2021)

141

Curve Color

You can select the color for the DAC / TGC curve.

DGS Mode

This parameter is only visible when 

DGS

 has been se-

lected in 

Eval Mode

.

You can switch this function on or off.

DGS Curve

This parameter is only visible when 

DGS

 has been se-

lected in 

Eval Mode

.

You must enter the reference size for the evaluation.

Probe Selection

This parameter is only visible when 

DGS

 has been se-

lected in 

Eval Mode

.

This is the same function as in the function group 

 

Material Probe

 (see page 117).

Probe Name

This parameter is only visible when 

DGS

 has been se-

lected in 

Eval Mode

.

This is the same function as in the function group 

 

Material Probe

 (see page 117).

Frequency

This parameter is only visible when 

DGS

 has been se-

lected in 

Eval Mode

.

This is the same function as in the function group 

 

Material Probe

 (see page 118).

Effective Diameter

This parameter is only visible when 

DGS

 has been se-

lected in 

Eval Mode

.

This is the same function as in the function group 

 

Material Probe

 (see page 118).

Summary of Contents for Krautkramer USM 10



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands