manualshive.com logo in svg

Waygate Technologies Krautkramer USM 10, Operating Manual

Share
Download
Waygate Technologies Krautkramer USM 10 Operating Manual Download Page 50

3  Initial start-up

Power supply

50

Rev. - (09/2021)

Krautkrämer USM 100

Charging the batteries

The internal battery is always charged automatically as 
soon as you connect the power adapter to the instru-
ment and to the mains power. 

You can charge the hot-swappable lithium-ion battery 
either within the instrument itself or in an external char-
ger. If the lithium-ion battery is inserted, charging starts 
automatically as soon as you connect the power adapt-
er to the instrument and to the mains power. 

Internal charging

Charging starts automatically as soon as you connect 
the power adapter to the USM 100 and to the mains 
power supply. You can carry out ultrasonic tests and 
charge the batteries at the same time. 

The charging time is approx. ten hours with simultane-
ous ultrasonic testing. If the instrument is not used for ul-
trasonic testing, the charging time is approx. eight 
hours. This charging time applies to ambient tempera-
tures of 25 … 30 °C. 

Charging status

All battery charge controls and status updates are inter-
nal to the USM 100. Updates are given at the upper right 
corner of the display as described on the previous page.

The power adapter is a simple power supply with no 
charging controls or intelligence. 

External charging

ATTENTION

Only chargers recommended and supplied 
by Waygate Technologies may be used for 
instrument operation.

Do not use any other chargers for charging 
the lithium-ion batteries for the USM 100.

Summary of Contents for Krautkramer USM 10



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands