manualshive.com logo in svg

Waygate Technologies Krautkramer USM 10, Operating Manual

Share
Download
Waygate Technologies Krautkramer USM 10 Operating Manual Download Page 121

Pulser Receiver

5  Operation

Krautkrämer USM 100

Rev. - (09/2021)

121

Averaging

This function is used to optimize the A-scan representa-
tion by averaging several A-scan frames to one frame.

Damping

This function is used for matching the probe. By setting 
the damping level of the probe oscillating circuit you can 
vary the height, width, and resolution of the echo dis-
play. 

400 Ohms

This setting gives a low damping, the echoes become 
higher and broader. 

50 Ohms

This setting reduces the echo height but produces nar-
rower echoes with a higher resolution. 

Filter

You can optimize the signal by setting a frequency filter 
until a clear echo is visible. Filter and damping influence 
each other. Therefore you need to try all possible com-
binations to achieve an optimal result.

Summary of Contents for Krautkramer USM 10



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands