manualshive.com logo in svg

Waygate Technologies Krautkramer USM 10, Operating Manual

Share
Download
Waygate Technologies Krautkramer USM 10 Operating Manual Download Page 170

5  Operation

DGS

170

Rev. - (09/2021)

Krautkrämer USM 100

trueDGS angle-beam probes

trueDGS

®

 angle-beam probes generate a rotationally 

symmetric sound field in the material to be tested like 
vertically beaming circular elements.

Because of this, the DGS evaluation using these angle-
beam probes is considerably more accurate than with 
the conventional angle-beam probes which contain rect-
angular elements. In the case of conventional angle-
beam probes, it may happen that the reflectors evaluat-
ed according to the DGS method are over-evaluated. 

The following probes using the trueDGS

® 

technology 

are currently available:

● MWB45-2 tD (probe # 

35

)

● MWB60-2 tD (probe # 

36

)

● MWB70-2 tD (probe # 

37

)

● MWB45-4 tD (probe # 

38

)

● MWB60-4 tD (probe # 

39

)

● MWB70-4 tD (probe # 

40

)

These new probes can be selected in the instrument. 
The corresponding settings are stored in the instrument 
and activated when the probe is selected.

Summary of Contents for Krautkramer USM 10



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands