Waygate Technologies Krautkramer USM 10 Operating Manual Download Page 40

Page: 40 / 242

2 Standard package and accessories

Accessories

Rev. - (09/2021)

Krautkrämer USM 100

148M5829

USM 100 Transport case

USM 100 transport case

148M5843

USB Type-C Adapter Docking Hub

USB-C dock for connecting to external monitor
through VGA/HDMI, SD card/USB & Ethernet

148M5831

Shoulder Strap

2-point shoulder strap

159M0234

Anti-Reflection Screen Protector

Screen protector for USM 100

022-505-604

PTPA--CBL MD-00LEMO RA 6'

Right angle Lemo #00 to Microdot cable

022-509-819

CABLE,LEMO-00 RT ANG/LEMO-00

Right angle Lemo #00 to Lemo #00 cable

022-509-820

CABLE,LEMO-00 RT ANG/LEMO-1

Right angle Lemo #00 to Lemo #1 cable

022-509-821

CABLE,LEMO-00 RT ANG/KBA 533

Right angle Lemo #00 to dual Lemo #00 (KBA 533)

022-509-822

CABLE,LEMO-00 RT ANG/BNC

Right angle Lemo #00 to BNC

081-018-700

PFA

BNC-Lemo 00 adapters (qty of 2 recommended)

022-509-749

CABLE,00 LEMO-BNC,6"OAL,SINGLE

6 inch right angle Lemo #00 to BNC adapter cable

Part No.

Short code

Description

Summary of Contents for Krautkramer USM 10


















































































































































































































































Search results

Summary of Contents for Krautkramer USM 10

Reviews:

Brands by name

Popular brands

Waygate Technologies Krautkramer USM 10, Operating Manual

Search results

Summary of Contents for Krautkramer USM 10

Reviews:

Brands by name

Popular brands