manualshive.com logo in svg

Waygate Technologies Krautkramer USM 10, Operating Manual

Share
Download
Waygate Technologies Krautkramer USM 10 Operating Manual Download Page 214

9  Appendix

Manufacturer

214

Rev. - (09/2021)

Krautkrämer USM 100

9.2 Manufacturer

The ultrasonic flaw detector USM 100 is manufactured 
by:

Baker Hughes Digital Solutions GmbH

 

Robert-Bosch-Straße 3

 

50354 Hürth

 

Germany

T +49 (0) 22 33 601 111

 

F +49 (0) 22 33 601 402

The USM 100 is manufactured according to the state-
of-the-art methods using high-quality components. 
Thorough in-process inspections or intermediate tests 
and a quality management system certified to DIN EN 
ISO 9001 ensure an optimum quality of conformance 
and workmanship of the instrument.

Should you nevertheless detect an error on your instru-
ment, power the instrument off and remove the batter-
ies. Inform your local Waygate Technologies customer 
service and support, indicating the error and describing 
it.

Keep the shipping container for any repairs possibly re-
quired which cannot be made on the spot.

If there is anything special that you would like to know 
about the use, handling, operation, and specifications of 
the instruments, please contact your nearest Waygate 
Technologies representative or turn directly to:

Baker Hughes Digital Solutions GmbH

Service-Center

 

Robert-Bosch-Straße 3

 

50354 Hürth

 

Germany

or:

Postfach 1363

 

50330 Hürth

 

Germany

T +49 (0) 22 33 601 111

 

F +49 (0) 22 33 601 402

Summary of Contents for Krautkramer USM 10



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands